The dies are split adjustable HSS. All are 1 1/2" outside diameter except the M22x0.75 Saiga-12 dies.
Click the part # to add to cart
1/2-28RH Dies & TATs
# DIE5028RH - $30 - 1/2-28RH Die for 0.500" to 0.520" o.d. barrels
# TAT5028RH545 - $15 - 1/2-28RH TAT for .22 & 5.45 cal barrels
# TAT5028RH223 - $15 - 1/2-28RH TAT for .223 cal barrels
# TAT5028RH30 - $15 - 1/2-28RH TAT for .30 cal barrels
M14x1LH Dies & TATs
# DIE14X1LH - $30 - M14X1LH Die for 0.551" to 0.571" o.d. barrels
# TAT14X1LH545 - $15 - M14X1LH TAT for .22 & 5.45 cal barrels
# TAT14X1LH223 - $15 - M14X1LH TAT for .223 cal barrels
# TAT14X1LH30 - $15 - M14X1LH TAT for .30 cal barrels
9/16-24LH Dies & TATs
# DIE5624LH - $30 - 9/16-24LH Die for 0.56" to 0.58" o.d. barrels
# TAT5624LH30 - $35 - 9/16-24LH TAT for .30 cal barrels
M15x1RH Dies & TATs
# DIE15X1RH - $30 - M15X1RH Die for 0.591" to 0.611" o.d. barrels
# TAT15X1RH545 - $25 - M15X1RH TAT for .22 & 5.45 cal barrels
# TAT15X1RH223 - $25 - M15X1RH TAT for .223 cal barrels
# TAT15X1RH30 - $19 - M15X1RH TAT for .30 cal barrels
5/8-24RH Dies & TATs
# DIE6324RH - $30 - 5/8-24RH Die for 0.625" to 0.645" o.d. barrels
# TAT6324RH30 - $19 - 5/8-24RH TAT for .30 cal barrels
M17x1RH Dies & TATs
# DIE17X1RH - $30 - M17X1RH Die for 0.669" to 0.689" o.d. barrels
# TAT17X1RH30 - $25 - M17X1RH TAT for 30 cal barrels, dished on the end for Saiga-308 muzzle taper
Saiga-410
# DIE15X075LH - $90 - M15X0.75LH Die for 0.591" to 0.611" o.d. barrels (factory Saiga-410)
# TAT15X075LH - $35 - M15X0.75LH TAT for cylinder bore Saiga-410 barrels
Saiga-20
# DIE20X075RH - $90 - M20X0.75RH Die for 0.787" to 0.807" o.d. barrels (factory Saiga-20)
# TAT20X075RH - $35 - M20X0.75RH TAT for cylinder bore Saiga-20 barrels
Saiga-12
# DIE22X075RH - $90 - M22X0.75RH Die for 0.866" to 0.886" o.d. barrels (factory Saiga-12) (2" OD die)
# TAT22X075RH - $35 - M22X0.75RH TAT for cylinder bore Saiga-12 barrels
Die Stock
# 1.5" DIESTOCK - $15 - Die Stock for holding 1.5" threading dies
Die Stock
# 2" DIESTOCK - $25 - Die Stock for holding 2" threading dies (M22x0.75)
Tips for Threading - Many times guys forget to remove the Thread Alignment Tool (TAT) after they get 4 or so threads started. They then bottom out the TAT on the barrel face and rip the threads out of the TAT, Die or both. Also don't just crank the die on there, it will break. Remember to break the chips (back off) after 1/6 to 1/4 of a turn so you don't load up the die. Be sure to use cutting fluid.
Proper Sizes - Just because you want a certain threading on your rifle, do not assume the threading die will work! Measure the barrel O.D. where you will be threading. If the diameter is 0.020" larger than the die size, forget about it. The die will break and/or your barrel will be screwed up. The recommended sizes above are assuming that you didn't cut your barrel back as most are tapered or increase in diameter the shorter you go.
Downloads:
Instructions for crowning your rifle or shotgun.
Muzzle Cutter Kit Instructions and Rental
